16/24-Port 10/100/1000Mbps
Gigabit Ethernet Switch
GSW-1601/GSW-2401/GSW-2416
User's Manual
Trademarks
Copyright © PLANET Technology Corp. 2007.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work
properly in all environments and applications, and makes no warranty
and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or fitness for a particular
purpose.
PLANET has made every effort to ensure that this User’s Manual is
accurate; PLANET disclaims liability for any inaccuracies or omissions
that may have occurred.
Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET
assumes no responsibility for any inaccuracies that may be contained in
this User’s Manual. PLANET makes no commitment to update or keep
current the information in this User’s Manual, and reserves the right
to make improvements to this User’s Manual and/or to the products
described in this User’s Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances in
electrical and electronic equipment, end users of electrical
and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 16/24-Port 10/100/1000Mbps Gigabit Ethernet Switch User's
Manual
For Models: GSW-1601/GSW-2401/GSW-2416
Revision: 2.1 (October 2007)
Part No: EM-GSW1624v4 (2010-A50140-004)
TABLE OF CONTENTS
1. INTRODUCTION.......................................................................... 6
1.1 Package Contents................................................................ 6
1.2 How to Use This Manual ..................................................... 6
1.3 Product Features ................................................................. 7
1.4 Product Specifications .......................................................... 8
2. INSTALLATION...........................................................................10
2.1 Product Description.............................................................10
2.1.1 Product Overview.......................................................10
2.1.2 Switch Front Panel .....................................................11
2.1.3 LED Indicators ...........................................................11
2.1.4 Switch Rear Panel ......................................................13
2.2 Installing the Switch...........................................................13
2.2.1 Desktop Installation....................................................14
2.2.2 Rack Mounting...........................................................15
3. Switch Operation .......................................................................17
3.1 Address Table.....................................................................17
3.2 Learning............................................................................17
3.3 Forwarding & Filtering.........................................................17
3.4 Store-and-Forward..............................................................17
3.5 Auto-Negotiation ................................................................18
4. Troubleshooting .........................................................................19
APPENDIX A NETWORKING CONNECTION........................................20
A.1 Switch‘s RJ-45 Pin Assignments...........................................20
A.2 RJ-45 cable Pin Assignments...............................................21
A.3 Install the Mini-GBIC module...............................................22
1. INTRODUCTION
1.1 Package Contents
Check the contents of your package for following parts:
● Gigabit Ethernet Switch x 1
● User's manual x 1
● Power cord x 1
● Rubber feet x 4
● Two rack-mounting brackets with attachment screws x1
If any of these are missing or damaged, please contact your dealer
immediately, if possible, retain the carton including the original packing
material, and use them against to repack the product in case there is a
need to return it to us for repair.
1.2 How to Use This Manual
This Gigabit Ethernet Switch User Manual is structured as follows:
Chapter 2 Installation
The chapter explains the feature, functionality and the physical
installation of the Gigabit Ethernet Switch.
Chapter 3 Switch operation
The chapter explains the Gigabit Ethernet Switch transmit operation.
Chapter 4 Troubleshooting
The chapter explains the troubleshooting of the Gigabit Ethernet
Switch.
Appendix A
This chapter contains cable information of the Gigabit Ethernet Switch.
In the following section, the term “Gigabit Ethernet Switch” means the
GSW-1601/GSW-2401 and GSW-2416.
ꢀ
1.3 Product Features
● Comply with IEEE 802.3, 10Base-T, IEEE 802.3u 100Base-TX, IEEE
802.3ab 1000Base-T, IEEE 802.3z 1000Base-SX/LX Ethernet standard
● 16/24-Port 10/100/1000Mbps Gigabit Ethernet ports
● 16-Port SFP (Small Form-factor Pluggable) for 3.3V mini GBIC
module, shared with port#9 to #24 (GSW-2416 only)
● Features Store-and-Forward mode with wire-speed filtering and
forwarding rates
● Hardware based 10/100Mbps, half / full duplex and 1000Mbps full
duplex mode, flow control and auto-negotiation
● IEEE 802.3x flow control for full duplex operation and Backpressure
for half duplex operation
● Integrated address look-up engine, support 8K absolute MAC
addresses
● 340/500/400K bytes on-chip frame buffer
● 9K Jumbo packet support
● Automatic address learning and address aging
● Supports Auto MDI/MDI-X function
● Support CSMA/CD protocol
● 100~240VAC, 50~60Hz universal Power input
● FCC, CE class A compliant
ꢁ
1.4 Product Specifications
GSW-1601 / GSW-2401 / GSW-2416
16/24-Port 10/100/1000Mbps Gigabit Ethernet
Switch
Product
Hardware Specification
16/24 10/100/1000Base-T RJ-45 Auto-MDI/
MDI-X ports
Ports
16 ports 3.3V mini-GBIC SFP, 1000Mbps full-
SFP Ports
duplex; shared with port #9 to port 24
(GSW-2416 only)
Switch
Store-and-Forward
Processing
Scheme
Throughput
(packet per
second)
GSW-1601: 23.8Mpps.
GSW-2401/GSW-2416: 35.7Mpps
GSW-1601: 32Gbps.
GSW-2401/GSW-2416: 48Gbps
Switch fabric
Address Table
8K entries
GSW-1601: 340K bytes on-chip frame buffer
GSW-2401: 500K bytes on-chip frame buffer
GSW-2416: 400K bytes on-chip frame buffer
Share data Buffer
Jumbo packet
size
9K
Back pressure for half duplex, IEEE 802.3x
Pause Frame for full duplex
Flow Control
GSW-1601/GSW-2401: 440 x 120 x 44 mm
(1U height)
GSW-2416: 440 x 200 x 44 mm (1U height)
Dimensions
(W x D x H)
GSW-1601: 1.54kg
GSW-2401: 1.64kg
GSW-2416: 2.6kg
Weight
ꢂ
Power
Requirement
100~240 VAC, 50-60 Hz
Power
Consumption /
Dissipation
GSW-1601/GSW-2401: 30 watts / 102BTU
GSW-2416: 130 watts / 443 BTU
Operating: 0~50 degree C
Storage -40~70 degree
Temperature
5% to 90%, Storage: 5% to 90% (Non-
condensing)
Humidity
Operating:
Standards Conformance
Regulation
FCC Part 15 Class A, CE
Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3z (Gigabit Ethernet)
IEEE 802.3x (Full-duplex flow control)
Standards
Compliance
ꢃ
2. INSTALLATION
This section describes the functionalities of the Gigabit Ethernet
Switch’s components and guides how to install it on the desktop.
Basic knowledge of networking is assumed. Please read this chapter
completely before continuing.
2.1 Product Description
The PLANET Gigabit Ethernet Switch is 10/100/1000Mbps Gigabit
Ethernet Switch with 16/24 ports respectively, and non-blocking wire-
speed performance. With 32/48Gbps internal switching fabric, the
Gigabit Ethernet Switch can handle extremely large amounts of data in
a secure topology linking to a backbone or high capacity servers.
The Gigabit Ethernet Switch has 8K MAC Address table and provides
340/400/500K bytes buffer memory. The Gigabit Ethernet Switch offers
wire-speed packets transfer performance without risk of packet loss.
The high data throughput of Gigabit Ethernet Switch makes it ideal
for most Gigabit environments, especially while network upgrades to a
Gigabit environment.
All RJ-45 copper interfaces support 10/100/1000Mbps Auto-Negotiation
for optimal speed detection through RJ-45 Category 6, 5 or 5e cables.
Support standard for Auto-MDI/MDI-X that can detect the type of
connection to any Ethernet device without requiring special straight or
crossover cables, the GSW-2416 provide 24 10/100/1000Base-T ports
and together with 16-SFP(Small Form-factor Pluggable). Shared with
port #9 to port #24, make the GSW-2416 be a 16-Port Gigabit fiber
Switch with mini-GBIC fiber-optic module installed that shall provide
long distance fiber connectivity.
2.1.1 Product Overview
The PLANET Gigabit Ethernet Switch with 16/24 RJ-45 10/100/1000Mbps
ports for high-speed network connectivity. The Gigabit Ethernet Switch
can also automatically identify and determine the correct transmission
speed and half/full duplex mode of the attached devices with its 16/24
ports. The Gigabit port with jumbo frame feature supported, can handle
10
extremely large amounts of data transmission in a secure topology
linking to a backbone or high-power servers.
The Gigabit Ethernet Switch also supports Store-and-Forward forwarding
scheme to ensure low latency and high data integrity, eliminates
unnecessary traffic and relieves congestion on critical network paths.
With an intelligent address recognition algorithm, the Gigabit Ethernet
Switch could recognize up to 8K different MAC address and enables
filtering and forwarding at full wire speed.
The Flow Control function allows your Gigabit Switch supported routers
and servers to directly connect to this Switch for fast, reliable data
transfer.
2.1.2 Switch Front Panel
Figure 2-1 & 2-2 & 2-3 shows a front panel of Gigabit Ethernet Switch.
Figure 2-1 GSW-1601 front panel
Figure 2-2 GSW-2401 front panel
Figure 2-3 GSW-2416 front panel
2.1.3 LED Indicators
GSW-1601/GSW-2401
System
LED
Color
Function
PWR
Green Lights to indicate that the Switch has power.
11
Per 10/100/1000Mbps port
LED
Color
Function
Lights to indicate that the Switch is successfully
connecting to the network at 1000Mbps.
Blinks to indicate the Switch is receiving or
sending data.
1000
Green
Off to indicate the Switch is connecting to the
network at 10Mbps or 100Mbps.
Lights to indicate that the Switch is successfully
connecting to the network at 100Mbps.
Blinks to indicate the Switch is receiving or
sending data.
10/100
Green
Off to indicate the Switch is connecting to the
network at 10Mbps or 1000Mbps.
GSW-2416
System
LED
Color
Function
PWR
Green
Lights to indicate that the Switch has power.
Per 10/100/1000Mbps port
LED
Color
Function
Lights to indicate that the Switch is successfully
connecting to the network at 1000Mbps.
Blinks to indicate the Switch is receiving or
sending data.
1000
LNK/
ACT
Green
Lights to indicate that the Switch is successfully
connecting to the network at 100Mbps.
Blinks to indicate the Switch is receiving or
sending data.
100
LNK/
ACT
Amber
12
Per SFP Interface
LED
Color
Function
Lights to indicate that the Switch is successfully
connecting to the network at 1000Mbps through
Green SFP interface.
Blinks to indicate the Switch is receiving or
sending data.
SFP
LNK/
ACT
2.1.4 Switch Rear Panel
Figure 2-4 & 2-5 shows a rear panel of Gigabit Ethernet Switch.
Figure 2-4 GSW-1601/GSW-2401 rear panel
Figure 2-5 GSW-2416 rear panel
Power Notice:
1.The device is a power-required device, it means, it will not work till
it is powered. If your networks should active all the time, please
consider using UPS (Uninterrupted Power Supply) for your device. It
will prevent you from network data loss or network downtime.
2.In some area, installing a surge suppression device may also help to
protect your Gigabit Ethernet Switch from being damaged by unregu-
lated surge or current to the Switch or the power adapter.
2.2 Installing the Switch
This part describes how to install your Gigabit Ethernet Switch and
make connections to it. Please read the following topics and perform
the procedures in the order being presented.
13
This Gigabit Ethernet Switch does not need software
configuration.
Note
2.2.1 Desktop Installation
To install the Gigabit Ethernet Switch on desktop, simply follow the
next steps:
Step 1: Attach the rubber feet to the recessed areas on the bottom
of the Gigabit Ethernet Switch.
Step 2: Place the Gigabit Ethernet Switch on desktop near an AC
power source.
Step 3: Keep enough ventilation space between the Gigabit Ethernet
Switch and the surrounding objects.
When choosing a location, please keep in mind the
environmental restrictions discussed in Chapter 1, Section
1.4 Product Specifications.
Note
Step 4: Connect your Gigabit Ethernet Switch to network devices.
A.Connect one end of a standard network cable to the 10/100/1000
RJ-45 ports on the front of the Gigabit Ethernet Switch.
B.Connect the other end of the cable to the network devices such as
printer servers, workstations or routers…etc.
Connection to the Gigabit Ethernet Switch requires UTP
Category 5 network cabling with RJ-45 tips. For more
information, please see the Cabling Specification in
Note
Appendix A.
Step 5: Supply power to the Gigabit Ethernet Switch.
A.Connect one end of the power cable to the Gigabit Ethernet Switch.
B.Connect the power plug of the power cable to a standard wall outlet.
When the Gigabit Ethernet Switch receives power, the Power LED
should remain solid Green.
14
2.2.2 Rack Mounting
To install the Gigabit Ethernet Switch in a 19-inch standard rack, follow
the instructions described below.
Step 1: Place your Gigabit Ethernet Switch on a hard flat surface,
with the front panel positioned towards your front side.
Step 2: Attach a rack-mount bracket to each side of the Switch with
supplied screws attached to the package. Figure 2-6 shows
how to attach brackets to one side of the Gigabit Ethernet
Switch.
Figure 2-6 Attaching the brackets to the Gigabit Ethernet Switch
Caution:
You must use the screws supplied with the mounting brackets. Damage
caused to the parts by using incorrect screws would invalidate your
warranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the
opposite side.
Step 5: After the brackets are attached to the Gigabit Ethernet
Switch, use suitable screws to securely attach the brackets to
the rack, as shown in Figure 2-7.
15
Figure 2-7 Mounting the Gigabit Ethernet Switch in a Rack
Step 6: Proceeds with the steps 4 and steps 5 of session 2.2.1
Desktop Installation to connect the network cabling and
supply power to your Gigabit Ethernet Switch.
1ꢀ
3. Switch Operation
3.1 Address Table
The Gigabit Ethernet Switch is implemented with an address table.
This address table composed of many entries. Each entry is used to
store the address information of some node in network, including MAC
address, port no, etc. This information comes from the learning process
of Gigabit Ethernet Switch.
3.2 Learning
When one packet comes in from any port. The Gigabit Ethernet
Switch will record the source address, port no. And the other related
information in address table. This information will be used to decide
either forwarding or filtering for future packets.
3.3 Forwarding & Filtering
When one packet comes from some port of the Gigabit Ethernet Switch,
it will also check the destination address besides the source address
learning. The Gigabit Ethernet Switch will lookup the address-table for
the destination address. If not found, this packet will be forwarded to
all the other ports except the port which this packet comes in. And
these ports will transmit this packet to the network it connected. If
found, and the destination address is located at different port from this
packet comes in, the Gigabit Ethernet Switch will forward this packet
to the port where this destination address is located according to the
information from address table. But, if the destination address is located
at the same port with this packet comes in, then this packet will be
filtered. Thereby increasing the network throughput and availability.
3.4 Store-and-Forward
Store-and-Forward is one type of packet-forwarding techniques. A
Store-and Forward Gigabit Ethernet Switch stores the incoming frame in
1ꢁ
an internal buffer, do the complete error checking before transmission.
Therefore, no error packets occurrence, it is the best choice when a
network needs efficiency and stability.
The Gigabit Ethernet Switch scans the destination address from the
packet-header, searches the routing table provided for the incoming
port and forwards the packet, only if required. The fast forwarding
makes the switch attractive for connecting servers directly to the
network, thereby increasing throughput and availability. However, the
switch is most commonly used to segment existing hubs, which nearly
always improves overall performance. An Ethernet Switching can be
easily configured in any Ethernet network environment to significantly
boost bandwidth using conventional cabling and adapters.
Due to the learning function of the Gigabit Ethernet Switch, the source
address and corresponding port number of each incoming and outgoing
packet are stored in a routing table. This information is subsequently
used to filter packets whose destination address is on the same
segment as the source address. This confines network traffic to its
respective domain, reducing the overall load on the network.
The Gigabit Ethernet Switch performs “Store and Forward" therefore,
no error packets occur. More reliably, it reduces the re-transmission
rate. No packet loss will occur.
3.5 Auto-Negotiation
The STP ports on the Gigabit Ethernet Switch have built-in “Auto-
negotiation”. This technology automatically sets the best possible
bandwidth when a connection is established with another network
device (usually at Power On or Reset). This is done by detect the
modes and speeds at the second of both device is connected and
capable of, both 10Base-T and 100Base-TX devices can connect with
the port in either Half- or Full-Duplex mode. 1000Base-T can be only
connected in Full-duplex mode.
1ꢂ
4. Troubleshooting
This chapter contains information to help you solve issues. If the
Gigabit Ethernet Switch is not functioning properly, make sure the
Ethernet Switch was set up according to instructions in this manual.
The per port LED is not lit
Solution:
Check the cable connection of the Gigabit Ethernet Switch.
Performance is bad
Solution:
Check the speed duplex mode of the partner device. The Gigabit
Ethernet Switch is run at Auto-negotiation mode and if the partner is
set to half duplex, then the performance will be poor.
Per port LED is lit, but the traffic is irregular
Solution:
Check that the attached device is not set to dedicate full duplex. Some
devices use a physical or software switch to change duplex modes.
Auto-negotiation may not recognize this type of full-duplex setting.
Why the Gigabit Ethernet Switch doesn’t connect to the
network
Solution:
Check per port LED on the Gigabit Ethernet Switch. Try another port
on the Gigabit Ethernet Switch Make sure the cable is installed properly
Make sure the cable is the right type Turn off the power. After a while,
turn on power again.
1ꢃ
APPENDIX A NETWORKING CONNECTION
A.1 Switch‘s RJ-45 Pin Assignments
1000Mbps, 1000Base-T
Contact
MDI
MDI-X
BI_DB+
BI_DB-
BI_DA+
BI_DD+
BI_DD-
BI_DA-
BI_DC+
BI_DC-
1
2
3
4
5
6
7
8
BI_DA+
BI_DA-
BI_DB+
BI_DC+
BI_DC-
BI_DB-
BI_DD+
BI_DD-
10/100Mbps, 10/100Base-TX
RJ-45 Connector pin assignment
MDI Media Dependant
MDI-X Media Dependant
Interface - Cross
Contact
Interface
1
2
Tx + (transmit)
Tx - (transmit)
Rx + (receive)
Rx + (receive)
Rx - (receive)
Tx + (transmit)
3
4, 5
6
Not used
Rx - (receive)
Tx - (transmit)
7, 8
Not used
20
A.2 RJ-45 cable Pin Assignments
The standard RJ-45 receptacle/connector
There are 8 wires on a standard UTP/STP cable and each wire is color-
coded. The following shows the pin allocation and color of straight cable
and crossover cable connection:
Figure A-1 Straight-Through and Crossover Cable
Please make sure your connected cables are with same pin assignment
and color as above picture before deploying the cables into your
network.
21
A.3 Install the Mini-GBIC module
Please follow these steps to install the Mini-GBIC modules:
1.Power on the Gigabit Ethernet Switch and place it on a flat surface.
Install the new Mini-GBIC modules by inserting it into the slots and
sliding it in until it stops (See Figure A-2). Press it firmly until you
feel the module snap into place. Never force, twist or bend the Mini-
GBIC modules. The Mini-GBIC module slides in smoothly and the
Gigabit Ethernet Switch will automatically detect the new module.
Figure A-2 Insert the Mini-GBIC modules
2.After the fiber connection was built successfully. Check the LEDs to
verify that if there is a link and a proper connection at the port.
22
This page is intentionally left blank
This page is intentionally left blank
|