AQ 5055 - Radio Cassette Recorder
Controls/ Installation
Radio/ Playback
CONTROLS
RADIO RECEPTION
•
•
•
Set the MODE selector 3 to RADIO.
Adjust the sound with the VOLUME 2 control.
For extra amplification of the bass, use the
DBB control 1. You may connect stereo
headphones with 3.5 mm plug to the socket p
PHONES 4. The loudspeakers are then
muted.
TOP AND FRONT PANEL - FIG. 1
1 DBB button - to switch the bass boost on and
off for extra bass.
2 VOLUME control - to adjust the volume level
3 MODE selector - to select the sound source:
English
–
–
TAPE/ (POWER OFF) - to switch to tape mode
RADIO/ (MONO/ STEREO)/ (POWER ON) - to
switch to radio mode
AQ 5055 Radio Cassette Recorder
•
•
Select the wave band using BAND switch 5.
Tune to a radio station using the TUNINGknob 6.
4 p PHONES stereo headphones socket -
connection for headphones
(impedance 8-32 ohms)
5 BAND switch - to select AM or FM
6 TUNING control - to tune to a radio station
7 6 FM ST - lights up when program is received
in stereo
8 MIC
9 RECORD 0 button
0 PLAY 1 button
! REW 6 button
– For FM, pull out the telescopic aerial. To
improve FM reception, incline and turn the
aerial. Reduce its length if the FM signal is too
strong (very close to a transmitter).
– For AM(MW), the set is provided with a built-in
aerial, so there is no need to use the telescopic
aerial. The aerial can be directed by turning the
whole set.
•
When FM ST 6 lights up, you are receiving a
FM stereo transmitter.
IOIO
OIO
A disturbing noise, due to a weak FM stereo
signal can be suppressed by setting the
MONO/STEREO switch 3 to MONO. The FM
ST 6 will disappear and you will hear (and
record) the FM program in MONO.
The set is switched off if the MODE selector
3 is in position TAPE and no buttons are
pressed.
IOIO
IOIO
OO
OIO
IO
OIO
@ F.FWD 5 button
# STOP/ EJ 9 3 button
$ PAUSE ; button
SIDE AND BACK PANEL - FIG 2
% Voltage selector (not all versions)
^ AC MAINS - socket for mains lead
& BEAT CUT switch - to eliminate possible
whistle tones during MW/AM recordings
* BATTERY compartment
FM
• • • • • • 88
•
92
96
100
900
104
106
108
•
•
•
MHz
KHz
A
M
• • • • • • 540
600
700
1100 1300 1500
1700
•
•
•
•
•
AUTOMATIC STOP MECHANISM
AUTOMATIC STOP MECHANISM
CASSETTE PLAYBACK
•
ONE TOUCH RECORDING
ONE TOUCH RECORDING
REC • PLAY
•
•
Set the MODE selector 3 to TAPE.
Press EJ 9 # and insert a recorded cassette
(fig. 3). For playback, any cassette type can be
inserted.
SUPPLY
Battery supply
•
Whenever convenient, use AC power supply if
you want to conserve battery life.
DDBBBB
ddyynnaammiiccbbaassssbboooosstt
•
Press PLAY 1 0 and playback will start
•
Open the battery compartment (fig. 2) and
insert six batteries as indicated , type R20,
UM1 or D-cells.
Remove the batteries if they are exhausted or
if they will not be used again for a long time.
The battery supply is switched off when the
set is connected to the power supply. To
change over to battery supply, pull out the plug
from the MAINS socket ^.
– Playback stops when the tape in the deck
reaches its end.
•
Adjust the sound with the VOLUME control
2. You may connect stereo headphones with
3.5 mm plug to socket p PHONES 4. The
loudspeakers then will be muted.
•
•
For extra amplification of the bass, use the
DBB control 1.
Instructions for use
•
•
To interrupt playback press PAUSE ; $.
Press STOP 9 # if you want to stop the
playback before the end of the tape.
When the end of the tape is reached, the PLAY
1 0 buttons are released.
DIG ITAL
Pow er supply
•
Make sure the power voltage as shown on the
type plate (on the back of the set) corresponds
to your local power voltage. If it does not,
consult your dealer or service organisation.
If the set is equiped with a voltage selector %
(fig. 2) set this selector to the local mains voltage.
Connect the power supply lead to the MAINS
socket and the wall socket. The mains supply
is switched on.
COMPACT CAS S ETTE
•
The set is switched off if the MODE selector
3 is in the TAPE position and no buttons are
pressed.
•
•
Winding the tape
•
•
•
Press F.FWD 5 to fast forward the tape.
Press REW 6 to fast rewind the tape.
Press STOP 9 to stop fast forward or fast
rewind, or before the end of the tape.
•
To disconnect the set from the power supply
completely, withdraw the mains plug from the
wall socket.
Im portant note for users in the UK,
see Troubleshooting
TC text/CvB/9551
|